- #MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE INSTALL#
- #MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE UPGRADE#
- #MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE SOFTWARE#
- #MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE SERIES#
!- This is the external Flash card and internal bootflash size. R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache !- The DRAM on the Supervisor is the sum of these two values.
#MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE SOFTWARE#
ROM: System Bootstrap, Version 5.3(1)īOOTFLASH: c6sup1_sp Software (c6sup1_sp-SPV-M), Version 12.1(8b)E9, !- This is the boot ROM version that runs on your switch supervisor.
![msm download tool device not match image msm download tool device not match image](https://piunikaweb.com/wp-content/uploads/2019/05/oneplus_7_pro_bootloader_download_mode.jpg)
Cat6500# remote command switch show version You can execute Supervisor Processor (SP) commands from the Route Processor (RP) prompt with the remote command switch command. You can also issue the show version command on the Supervisor module. 16384K bytes of Flash internal SIMM (Sector size 256K). SuperLAT software (copyright 1990 by Meridian Technology Corp).Ģ Virtual Ethernet/IEEE 802.3 interface(s)ġ8 Gigabit Ethernet/IEEE 802.3 interface(s)ģ81K bytes of non-volatile configuration memory. R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache cisco Catalyst 6000 (R5000) processor with 114688K/16384K bytes of memory.
![msm download tool device not match image msm download tool device not match image](https://1.bp.blogspot.com/-kOlSPVR1-ns/Xf4fsbvmEQI/AAAAAAAAECY/tZanupMHhGkbd-QRJiFYu_PyLSM_EgcnACNcBGAsYHQ/s1600/79452364_827177947752464_8047708031875547136_n.jpg)
!- The DRAM on the MSFC is the sum of these two values. System returned to ROM by power-on (SP by reload) ROM: System Bootstrap, Version 12.0(3)XE, RELEASE SOFTWAREīOOTFLASH: MSFC Software (C6MSFC-BOOT-M), Version 12.1(8b)E9, EARLY DEPLOYMENT !- This is the Boot ROM version that runs on your switch MSFC. IOS (tm) c6sup1_rp Software (c6sup1_rp-JSV-M), Version 12.1(8b)E9, EARLY DEPLOYMENTĬopyright (c) 1986-2002 by cisco Systems, Inc. Cat6500# show versionĬisco Internetwork Operating System Software Issue the show version command on Catalyst 6000/6500 switches that run Cisco IOS Software. When you run Cisco IOS Software, check the memory requirements on both the Supervisor and MSFC. !- This is the amount of DRAM and Flash size installed on the switch. !- This is the boot ROM version that runs on your switch. Issue the show version command on Catalyst 6000/6500 switches that run CatOS. The show version command displays the BootROM version, DRAM installed and the bootflash size on your switch.
#MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE SERIES#
Refer to Release Notes for Catalyst 6000/6500 Series Switches in order to verify the requirements for the new software image. Check whether your switch supports the requirements. Verify the minimum amount of DRAM, flash memory and Boot ROM version necessary for the new software release. Pre-Upgrade Steps Check Memory and Boot ROM Requirement Note: Refer to Comparison of the Cisco Catalyst and Cisco IOS Operating Systems for the Cisco Catalyst 6500 Series Switch for more information.
![msm download tool device not match image msm download tool device not match image](https://www.droidwin.com/wp-content/uploads/2020/11/uninstall-device.jpg)
You can use a single Cisco IOS image as the system software in order to run both the Supervisor and MSFC on Catalyst 6500/6000 switches. If the optional Multilayer Switch Feature Card (MSFC) is installed, use a separate Cisco IOS image in order to run the MSFC.Ĭisco IOS on both the Supervisor and MSFC (Native): You can use a CatOS image as the system software in order to run the Supervisor on Catalyst 6500/6000 switches. Difference Between CatOS and Cisco IOS System SoftwareĬatOS on the Supervisor and Cisco IOS on the MSFC (Hybrid): Refer to the Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
![msm download tool device not match image msm download tool device not match image](https://www.droidthunder.com/wp-content/uploads/2021/04/MSM-Download-Tool-featured-img.jpg)
This document is not restricted to specific software and hardware versions. Verify the memory and boot ROM requirements.īack up the current switch configuration and software image.
#MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE INSTALL#
You want to install a new line card that is not supported by the current software version that you run on the switch.Ī known bug affects your switch, and that bug is resolved in the next software release.Įnsure that you meet these requirements before you attempt this configuration: You want to implement new features in your network that are available in the new software release.
#MSM DOWNLOAD TOOL DEVICE NOT MATCH IMAGE UPGRADE#
The software image upgrade is necessary when: This document explains the step-by-step procedure to upgrade the software image on Catalyst 6000/6500 series switches that run Catalyst Operating System (CatOS) on Supervisor, Cisco IOS® on MSM/MSFC and Cisco IOS System Software.